BathSelect Technical Resources
Installation Instructions for
Architects & Designers
Plan bathroom fixture installation with model-specific guidance,
rough-in coordination and technical documentation. BathSelect
resources support architects, designers, contractors and project
teams working with shower systems, faucets, touchless fixtures,
soap dispensers and other bathroom products.
Before Rough-In
Confirm the Exact Product First
Installation requirements can differ by fixture, valve,
power configuration and product generation. Identify the
exact BathSelect model and review its available installation
documentation before finalizing rough-in or concealed work.
Model
Confirm the exact product and configuration.
Dimensions
Review applicable mounting and clearance data.
Connections
Verify water, power and control requirements.
Service Access
Plan access to concealed service components.
Pre-Installation Planning
What to Verify Before Installation Begins
Technical coordination before rough-in can help avoid
installation conflicts, inaccessible service components and
incorrect product placement.
Product
Exact Model & Configuration
Confirm the product name, model, finish and included
components before using dimensional information.
Rough-In
Mounting & Clearances
Review mounting location, wall or deck conditions,
rough-in depth and service clearances.
Utilities
Water & Power
Verify applicable supply connections, hot and cold
requirements, power source and control locations.
Coordination
Adjacent Construction
Coordinate cabinetry, waterproofing, tile, structure,
electrical work and access panels around the fixture.
Installation by Product Type
Find the Relevant Fixture Documentation
Start with the product family, then use the exact model
documentation whenever it is available.
Shower Systems
Shower Installation Resources
Review shower-head locations, concealed valves,
diverters, body jets, handhelds and supply planning.
Bathroom Faucets
Faucet Installation Resources
Review deck or wall mounting, supply connections,
spout placement and basin coordination.
Touchless Faucets
Sensor Faucet Installation
Coordinate faucet placement, sensor components,
control boxes, power and water connections.
Soap Dispensers
Automatic Dispenser Installation
Review deck penetration, reservoir placement,
tubing, sensor location and power requirements.
Bathtubs
Bathtub Installation Planning
Review product dimensions, drainage, supply,
support conditions and service requirements.
Sinks & Basins
Basin Installation Planning
Coordinate sink dimensions, countertop openings,
faucet placement, drains and clearances.
Rough-In Coordination
Coordinate What Will Be Concealed
The most important installation decisions often happen
before finished surfaces are complete. Concealed valves,
power supplies, control boxes, plumbing connections and
service access should be coordinated with the exact product
documentation and surrounding construction.
Wall Conditions
Rough-In Depth
Confirm wall build-up and applicable valve depth
before tile, stone or other finished surfaces are installed.
Deck Conditions
Countertop Thickness
Review allowable deck thickness, mounting hardware
and below-deck space for faucet or dispenser components.
Serviceability
Access Panels
Plan practical access to concealed controls,
solenoids, power supplies, valves and serviceable components.
Coordination
Fixture Relationships
Check basin, faucet, dispenser, shower and adjacent
components together rather than in isolation.
Installation Workflow
A Practical Coordination Sequence
The exact steps depend on the product, but project teams
can use this framework to organize technical review and installation.
Review
Confirm Product Documentation
Match the instructions, dimensions and technical
information to the actual model being installed.
Coordinate
Prepare Rough-In
Establish mounting locations, supply positions,
control locations, framing and access requirements.
Install
Complete Fixture Installation
Follow the product-specific sequence for mounting,
connections, controls and final fixture assembly.
Verify
Test Before Handover
Check water flow, leaks, operation, sensors,
temperature controls and accessible service components.
Touchless & Electronic Fixtures
Coordinate Plumbing and Power Together
Automatic faucets and dispensers can require additional
coordination beyond conventional plumbing fixtures.
Power Coordination
AC, DC & Control Components
Review the applicable power configuration and identify
locations for adapters, battery packs, control boxes,
cables and accessible connections before installation.
Sensor Coordination
Detection Area & Fixture Placement
Coordinate product position with the intended hand-use
area, basin geometry and nearby surfaces. Follow the
model-specific sensor and installation instructions rather
than assuming one detection setup applies to every fixture.
Important Technical Note
Model-Specific Instructions Take Priority
This page is a planning and coordination resource, not a
substitute for the installation document supplied for a
particular BathSelect product. Dimensions, rough-in locations,
connection methods, valve depths, electrical requirements and
component arrangements may vary between models. When exact
product documentation is available, use that information for
final installation decisions.
Testing & Commissioning
Verify Operation Before Project Handover
Complete functional checks while the relevant components
remain accessible whenever practical.
Plumbing
Check Flow & Leaks
Inspect accessible supply and fixture connections,
run each outlet and confirm expected water delivery.
Controls
Verify Functions
Test diverters, thermostatic controls, handles,
sensors and other user-operated functions.
Handover
Preserve Documentation
Keep installation instructions, model information,
specifications and applicable service documentation
with project records.
Technical Project Resources
Continue With the Documentation You Need
Use installation instructions together with the applicable
specifications, BIM, maintenance and warranty resources.
Missing Installation Document?
What to Include With Your Request
If you cannot locate the installation instructions for a
specific product, provide enough information for the
BathSelect team to identify the exact fixture and documentation.
Product
Model or Product Name
Provide the exact model, product title or product-page reference.
Configuration
Mounting & System Type
Identify wall mount, deck mount, ceiling mount,
concealed or other applicable configuration.
Project
Current Installation Stage
Explain whether the request is for design,
rough-in, active installation or service coordination.
Question
Specific Technical Need
Describe the dimension, connection, mounting or
documentation question that needs clarification.
BathSelect Technical Support
Need Product-Specific Installation Instructions?
Have the BathSelect product name or model available and include
the project stage and technical question. This helps identify
the relevant installation instructions, specification information
or next technical resource.
Request Technical Documentation
→
|
|
|
.png)
