 |
 |
 |
|
BathSelect Lima Multi Color Water Powered Flush Mount Led Showerhead with Adjustable Body Jets and Digital Control Mixer
Turn on the fun in your shower and experience the true feeling of rain, as well as SPA body massage spray, relieving fatigue and stress just by turning on the water in a high-pressure bathroom head shower with 360° 6 adjustable body spray jets and a hand shower. This shower set has been made with premium-grade lightweight and the LED lights will automatically light up and set the mood. They will even change colors automatically based on the water temperature. All this with no batteries, everything is self-powered by a built-in dynamo that takes advantage of the water pressure to create the energy to light the bulbs.
BathSelect Lima Multi Color Water Powered Led Shower with Adjustable Body Jets and Digital Mixer Features:
- Brand Name: BathSelect
- Model Number: BT-892RBD
- Material: Solid Brass
- Finish: Oil Rubbed Bronze
- Water Flow: Rainfall
- Showerhead Height (thickness): 0.33
- Showerhead Width: 20"
- Showerhead Length: 14"
- LED Power Source: Water Flow
- LED Color: Available without changing color or with LED colors Blue, Green, Red
- Shower Style: Recessed Rain Showerhead
- Connection: 1/2" US standard (included)
- Body Jets: Comes with solid brass 360° adjustable Body Jets size 5" x 5"
- Controller: Digital Smart Control
|
|
BathSelect® Manufacturer Warranty Information
 BathSelect Lima Multi Color Water Powered Led Shower Installation Instructions
Installation Instructions 1. Attach the upper wall support to the shower wall using a drill and the mounting hardware provided. Use a level to ensure that the shower riser is perfectly straight. 2. Place thread sealant on the ½” pipe threads on the shower wall and thread on the mounting nuts. Allow the sealant to cure for 24 hours before use. 3. Attach the hot and cold valve bodies and decorative escutcheons (if included) directly to the pipe threads. Tighten with an adjustable wrench to secure. 4. To install a hand-held shower, mount the cradle at a suitable height for the user with the hardware provided. Attach the hose to the faucet with any rubber washers or sealing gaskets included. If your system does not feature a hand-held shower move on to the next step. 5. Attach the showerhead to the top of the riser and tighten with a smooth jaw wrench. Do not tighten more than ¼ turn beyond hand tight. 6. Turn on the water supply and open the faucet valves. Check for any leaks and verify that the hot and cold supplies are working correctly. Let the water flow through the riser pipe and shower hose for approximately 30 seconds to clear out debris and dirt. Note: If leakage occurs, tighten connections with your adjustable wrench as necessary. If problems persist, contact Customer Service.
 | 
Rainfall | 
Self-cleaning silica gel | 
-> Water inlet
-> Voltage inverter | 
-> 304 Stainless steel polished.
-> Dimensions : 19.7"x14.2" | 
External Power Source: 200v transform into 12v
Overhead shower head decomposition. |
According to the dimensions and shape of the mounting bracket, determine the bracket location to be installed in the ceiling.
Showerhead lists :
-> Showerhead
-> 11.8" shower hose
-> Tee joint
-> Expansion bolt
-> G1/2" filter net
-> H4 inner hexagon. | 
Attention1. Open packages, check all the goods whether everything is ok. 2. Check the size of the connector and the thread size of the water pipes connector in the wall. 3. Clean the water pipes before installing them. 4. At least 2 water electricians to install the showerhead. 5. Pay attention to the water temperature, not over 70 degrees. 6. Water pressure: 0.05 MPA - 0.5 MPA. 7. Adapter is 100-265 V to 12 V, insurance device rated current less than 30 MA. | | According to the four mounting holes on the mounting bracket, use Electric drill play mounting holes. | | 
a) Through the two hexagonal nuts adjust the distance between the mounting bracket and the ceiling, and keep the mounting bracket on the level.
b) Use explosion screw fixed mounting bracket on the ceiling, pay attention to the explosion screw can adjust the height, and use level adjust the mounting bracket to level. | 
Connect 1 pcs water hose to 1 Tee Joints and G1/2, G1/2 joint in the middle, then put another side of the shower hose through the hole of shower head size. | 
Install the decorative panel, use SW4 hexagon wrench tighten 4 screws.
|  |
Hand-Held Shower Instructions Body-Jet Installation
Water Supply
Nipple Mamelon Nipple· Pressure Balancing Loop
1. Route the water supply lines. 2. If installing more than one bodyspray off the same supply line, construct a pressure balancing loop. Locate a tee along the loop at each bodyspray installation location. 3. Do not strap the pipes at this time.
Single Bodyspray Installation · Nipple Mamelon Nipple 1. Route the water supply line. 2. Install an elbow to the end of the supply pipe at the bodyspray installation location. | 
Install the Plaster Guard· Elbow (or Tee) · Install the plaster guard Set Piping Depth Align mark with the front of the stud face · Thin Wall Align mark with the front of the stud face · Standard Wall Install the plaster guard. Push until the plaster guard is snug against the face of the elbow (or tee).
| | 
1. Install the water-resistant wallboard. 2. Cut out a 4" (10.2 cm) to 4-1/4" (10.8 cm) square at each of the installation location. 3. Install the finished wall material
| 
1. Insert the escutcheon into the rough opening. The double ribs of the leak shield should be facing up. 2. If the leak shield makes contact with the elbow: Enlarge the hole in the back of the leak shield to 1-1/4" (3.2 cm). 3. Thread the adapter onto the nipple using the provided 11 mm bit, 11 mm or 7/16" socket, extension and socket wrench. Use masking tape to hold the bit in place, as the bit could fall off and cause damage. IMPORTANT! The escutcheon should sit loosely at this point. If it is tight against the wall, use a longer pipe nipple. 4. Align the groove in the waterway with the double ribs on the leak shield. 5. Press the waterway into place over the adapter. Secure the waterway to the adapter with the screw provided. 6. Verify that the escutcheon does not turn or shift.
· Escutcheon
· Leak Shield
· Adapter
· Extension
· Socket Wrench With Bit
· Screw
· Waterway Passage | | 
With the ribs of the spray head facing up, install the spray head to the waterway.
|  | |
 
|
|
|
 |
|
 |
|
|
|
Serves the Purpose, looks good! 
One jet missing