Installation Instructions
Shower
No. | Name | Quantity | No. | Name | Quantity |
1. | Bracket | 1 | 5. | Hexagon Wrench | 1 |
2. | M10 Explosion
Screw | 4 | 6. | Power | 1 |
3. | Shower
Assembly | 1 | 7. | Water Inlet
Connecting Pipe | 4 |
4. | Lock Screws | 4 | |
|
|
1. Use a hexagon wrench to lose the lock screws then separate the showerhead assembly and bracket.
2. Dig 4 Ø10 holes on the ceiling according to the dimension of the screws.
3. Use a hammer to thwack the 4 screws into 4 holes.
4. Install the bracket on the expansion screws then use copper sleeve wrench to lock 4 screws.
5. Make sure all the water inlet pipe connected well without leaking before insert the power plug into the socket.
6. Fix the shower assembly on the bracket by turn the locking bolt.
Mixer Installation
a. Release Six handwheel levers according to above directions.
b. Take apart the embed valve, panel, and handwheel.
1. Dig the embed space for the pipe on the wall according the specification of the valve.
2. Dig 4 hole according to the position of the screws.
3. Use a hammer to thwack the screws into 4 holes.
4. Fix the valve body with 4 screws.
5. Find out the expansion screw heads with washer and spring washer. Use copper sleeve wrench to lock the screw heads with the embed valve body.
6. After connect all the pipes and before sealing the wall with concrete, confirm no leaking problem occur when turn on water.
7. Fix the decorative panel on the embed valve body.
8. Screw the handwheel arms with the handwheels.
Hand-Held Shower
Shower Holder Installation
1. Open the closed cover of the shower holder and take out the screws.
2. Drill two holes size 6mm on the wall according the hole position of the shower holder. Use a hammer to break 2 plastic wall plug into two holes. Tighten the screws with the plastic wall plug and locking with the shower holder. Then install the closed cover.
3. Connect the shower hose with water outlet connection part and hand shower. Plug the hand shower in the shower holder.
Body-Jet Installation
Water Supply
Nipple Mamelon Nipple· Pressure Balancing Loop
1. Route the water supply lines. 2. If installing more than one bodyspray off the same supply line, construct a pressure balancing loop. Locate a tee along the loop at each bodyspray installation location. 3. Do not strap the pipes at this time.
Single Bodyspray Installation · Nipple Mamelon Nipple 1. Route the water supply line. 2. Install an elbow to the end of the supply pipe at the bodyspray installation location. | 
Install the Plaster Guard· Elbow (or Tee) · Install the plaster guard Set Piping Depth Align mark with the front of the stud face · Thin Wall Align mark with the front of the stud face · Standard Wall Install the plaster guard. Push until the plaster guard is snug against the face of the elbow (or tee).
| |
1. Install the water-resistant wallboard. 2. Cut out a 4" (10.2 cm) to 4-1/4" (10.8 cm) square at each of the installation location. 3. Install the finished wall material
| 
1. Insert the escutcheon into the rough opening. The double ribs of the leak shield should be facing up. 2. If the leak shield makes contact with the elbow: Enlarge the hole in the back of the leak shield to 1-1/4" (3.2 cm). 3. Thread the adapter onto the nipple using the provided 11 mm bit, 11 mm or 7/16" socket, extension and socket wrench. Use masking tape to hold the bit in place, as the bit could fall off and cause damage. IMPORTANT! The escutcheon should sit loosely at this point. If it is tight against the wall, use a longer pipe nipple. 4. Align the groove in the waterway with the double ribs on the leak shield. 5. Press the waterway into place over the adapter. Secure the waterway to the adapter with the screw provided. 6. Verify that the escutcheon does not turn or shift.
· Escutcheon
· Leak Shield
· Adapter
· Extension
· Socket Wrench With Bit
· Screw
· Waterway Passage | |
With the ribs of the spray head facing up, install the spray head to the waterway.
|  | |
UPGRADE YOUR SHOWER RIGHT NOW 
