Installation Instruction For Rennes Wall Mount Dual Cross Handle Bathroom Faucet Rennes Matte Black Finish Wall Mount Dual Cross Handle Bathroom Faucet This exquisite faucet in matte black finish elevates the decor of your bathroom it is made with the highest quality and for great tastes. Our wall mount 3 piece chrome faucet set is an elegant solution when deck mount is not an option. The handles have a cross design which makes it look elegant and classic. It is very easy to install and it can be installed as a wall mount. It requires three holes for the installation. It comes with a super seal technology inside, capable of delivering superior performance. It is drip free, leak free, & rust free. It has separate handles for hot and cold water and built-in water mixer. Only the best quality materials have been used – the body and handles are made of solid brass, as well as the valve core material is also brass. It comes complete with accessories and installation instructions. Rennes Matt Finish Wall Mount Dual Cross Handle Bathroom Faucet Features: Type : Bathroom faucets Style : Three hole handle Model Number : BS9828 Surface treatment : Matte Black Hot and cold water : Yes Type : Ceramic spool plate Style : Contemporary Installation Type : Wall Mount Handle number : Dual handle Package weight : 4.4 gal (2 KG) Valve core material : Brass Cold & Hot Water : Yes BathSelect® Manufacturer Warranty Information

Wall-Mount Lavatory Faucet Trim

Before You Begin

• Shut off the main water supply.
• Observe all local plumbing and building codes.
• If needed, complete the finished wall before beginning this installation.
• Reserves the right to make revisions in the design of faucets without notice, as specified in the Price Book.

1. Install the Spout

IMPORTANT! Use care when installing the spout to avoid scratching the finish.

• Thread the spout into the spout shank until it is snug. If needed, adjust the spout slightly to position it so it points straight down.
• Secure the spout in place by tightening the flange with the screws provided. Confirm that the O-ring is inside the escutcheon.
• Apply plumbers putty or other sealant to the back surface of the spout escutcheon according to the putty manufacturer’s instructions.
• Carefully slide the spout escutcheon over the spout and press firmly against the finished wall.
• Remove any excess putty or sealant

2. Install the Handles

NOTE: If the finished wall is less than 5/8″ (1.6 cm) thick, no spline adapter will be used with the installation.

• Determine the thickness of the finished wall.
• If the finished wall is less than 5/8″ (1.6 cm) thick, use the 1″ (2.5 cm) long stem extension, 7/8″ (2.2 cm) long screw, and the 2″ (5.1 cm) long threaded sleeve.
• If the finished wall is 5/8″ (1.6 cm) to 1-1/4″ (3.2 cm) thick, use the 1038270 hardware kit supplied.
• If applicable, slide a spline adaptor onto the stem extension.
• Place a stem extension the valve stem. Secure with the screw provided. Thread a threaded sleeve onto the valve body.
• Apply plumbers putty or other sealant to the back of the escutcheon according to the putty manufacturer’s instructions.
• Thread an escutcheon onto the threaded sleeve. Remove any excess putty or sealant.
• Press a handle over the stem extension and move the handle to the closed position (Hot = Counterclockwise, Cold = Clockwise). Lever handles should be horizontal when closed.

• If adjustment is needed to achieve the desired handle alignment, remove the handle, screw and spline adapter or stem extension. Turn the spline adapter 1/4 turn. Check the handle position. Repeat the procedure until the proper handle position is achieved. Secure with the screw.
• Thread the handle assembly onto the escutcheon. To maintain the proper handle alignment, hold the handle in place with one hand and turn the base of the handle with the other hand.
• Repeat the procedures with the second handle.

3. Complete the Installation

• Ensure that both faucet handles are turned off (hot = counterclockwise to close, cold = clockwise to close).
• Turn on the water supplies and check the installation for leaks.
• Repair as needed.
• Remove the aerator.
• Open the valves and run water through the spout for about a minute to remove any debris. Check for leaks.
• Remove all debris from the aerator.
• Turn the valves off, and reinstall the aerator.

• 2 cross handles for quick and easy water control
• Low-arc spout with a 6-1/4 in. reach for ample room in the sink
• Low-flow aerator option available (not included)
• Solid brass construction for durability and reliability
• Polished chrome finish resists corrosion and tarnishing for lasting beauty
• Fluid design lines for ease of cleaning
• Modern, minimal design is sure to coordinate well with the Purist suite and accessories
• Rough-in valve sold separately
• ADA compliant
• For a wall-mount installation