Home > Installation Instructions Bathselect Round Oil-Rubbed Bronze 8” Rainfall Wall Shower Head With Hand-Held Shower

BathSelect Round Oil-Rubbed Bronze 8” Rainfall Wall Shower Head with Hand-Held Shower

Stylish BathSelect round comes in a bathroom shower-head, & 8” size & amazing looks. Very attractive and fabulous looks and gives you a classic look to your bathroom. It comes in oil-rubbed bronze. It also has water saving function with this product.

Bathselect Antique Bathroom Shower Head:

  1. Type: Shower Head System
  2. Installation: US Standard
  3. Installation Mount: Wall Mount
  4. Customize: Yes
  5. Feature: Cold & Hot Water
  6. Size: 8” inches
  7. Core Material: Ceramic
  8. Style: Contemporary
  9. Shape: Square
  10. Rotatable Fixture: Yes
  11. Surface Finish: Brass
  12. Number of Handle: Single Lever
  13. Surface Treatment: Oil-Rubbed Bronze
  14. Type of Cold/ Hot Water Control: Dual Control of a Single Support
Bathselect Round Oil-Rubbed Bronze 8” Rainfall Wall Shower Head with Hand-Held Shower
BathSelect® Manufacturer Warranty Information

Installation Instructions for Rainfall Wall Shower Head With Hand-Held Shower


How to Install Bathselect Round Oil-Rubbed Bronze 8” Rainfall Wall Shower Head With Hand-Held Shower

  • Before you begin, please read the installation instructions below. Observe all local building and safety codes.
  • Unpack and inspect the product for any shipping damages. If you find damages, do not install.
  • Please note all showers must be installed by a professional and certified plumber otherwise warranty might be voided.
shower Bathselect Round Oil-Rubbed Bronze

Shower Specifications

shower install



Shower Head Installation Instructions

Step 1: Step 2:
Wall Mount Round Showerhead Showerhead
Wall Mount Round Showerhead
Step 3: Step 4:
Step 5: Step 6:


1. Apply plumber’s tape to the threads on both ends of the shower arm and slide on the decorative escutcheon.
2. Insert the new arm into the fitting in the wall or ceiling and twist to tighten. Finish tightening with your adjustable wrench. Wrap a dry cloth around the shower arm to protect the finish while tightening with an adjustable wrench.
Note: If your shower head does not feature a shower arm, connect the shower head directly to the fitting in the wall or ceiling.
3. Thread the new showerhead onto the arm and hand-tighten. Hold the shower arm in place with groove joint pliers and finish tightening the showerhead with your adjustable wrench. Wrap both in a dry cloth to protect the finish.
4. Before securing the decorative escutcheon to the wall, turn on the water supply to make sure that all connections are tight and there is no leaking. If no leaks are detected, continue with the installation. If leakage does occur, use your adjustable wrench to tighten the connections as necessary.
5. Apply a bead of silicone sealant to the back of the escutcheon and press firmly into place against the installation surface. Wipe away any excess sealant with your damp cloth.
6. Install the handle faceplate with the installation hardware.
7. Make sure the valve is in the OFF position and install your shower handle. Tighten the set screw in the middle or side of the handle to secure the handle in place.

Mixer Installation Instructions

Step 1: Step 2:
mixer

Hand Held Shower Installation Instructions

Step 1: Step 2:

handshower

Step 3: Step 4:
Step 5: Step 6:


Hand Shower Outlet Installation
• Complete the outlet pipework ensuring it ends in an appropriate 15mm x 1/2" BSP female thread elbow.

Note:
This fitting is not supplied as variations in installations require the selection of a suitable solder or compression fitting.

• Install the 'Wall Outlet', thread long male 1/2" BSP into the appropriate female fitting using PTFE tape to give a watertight joint.

Note: The thread can be cut to size if required. Make sure that all debris is removed from the connector and the section that has been cut is dressed correctly, before installation.

Shower Wall Holder Installation
Decide the position for the shower head holder on the wall within the bath showering area and proceed as follows:
• Hold the hand shower head holder fixing plate in a suitable position on the wall, mark out the position of the holder. Mark the two locating holes, these are 17mm center.
• Drill and plug the wall. Use an appropriate masonary drill, but if the wall is plasterboard or a soft building block, use special wall plugs and an appropriate drill bit.
• Slide the inserts onto the screws in the orientation. Secure the inserts by tightening the screws.
• Slide the hand shower head holder body onto the inserts and secure by tightening the grub screw facing down.




BathSelect Ancient Round Antique Rainfall Wall ShoweBathSelect Ancient Round Antique Rainfall Wall Shower Head Installation Instructions Head Installation Instructions