Home > The Naples Brushed Nickel Dual Handle Bathroom Sink Faucet Installation Details

Installation Instructions for Naples Brushed Nickel Dual Handle Bathroom Sink Faucet

Naples Brushed Nickel Dual Handle Bathroom Sink Faucet

Naples is a different kind of bathroom sink faucet: with a minimalist design, soft curves and elegant brushed nickel finish it will perfectly fit in any modern bathroom, regardless of the design. It is wall mount, 8” spread and it requires 3 holes for installations, as it comes with separate handles for hot and cold water. Only the best materials have been used: the body is made of solid brass and the valve core material is ceramic for a long-lasting lifetime. It is easy to install, as it has standard US connections and it comes complete with accessories and installation instructions.

Naples Brushed Nickel Dual Handle Bathroom Sink Faucet

  • Type : Bathroom Sink Faucet
  • Finish : Brushed Nickel
  • Installation : Wall-Mount
  • Control Handle : Dual Lever Water and Temperature Control
  • Configuration : Three-Hole Wall Mount
  • Material : Solid Brass with Ceramic Cartridge
  • Dimensions : 7" Spout Reach, 8" Spread
  • Included : All Mounting Hardware and Hot/Cold Waterlines
  • Rough-In Valve
  • Standard US Plumbing Connections
  • Not Included : Matching Drain.Naples Brushed Nickel Dual Handle Bathroom Sink Faucet
Naples Brushed Nickel Dual Handle Bathroom Sink Faucet
athSelect® Manufacturer Warranty Information

Before You Begin

  • Shut off the main water supply.
  • Observe all local plumbing and building codes.
  • If needed, complete the finished wall before beginning this installation.
wall-mount-3-piece-chrome-faucet-set1

Wall-Mount Lavatory Faucet Trim

1. Install the Spout

IMPORTANT! Use care when installing the spout to avoid scratching the finish.

  • Thread the spout into the spout shank until it is snug. If needed, adjust the spout slightly to position it so it points straight down.
  • Secure the spout in place by tightening the flange with the screws provided. Confirm that the O-ring is inside the escutcheon.
  • Apply plumbers putty or another sealant to the back surface of the spout escutcheon according to the putty manufacturer’s instructions.
  • Carefully slide the spout escutcheon over the spout and press firmly against the finished wall.
  • Remove any excess putty or sealant

Wall-Mount Lavatory Faucet Trim

2. Install the Handles

NOTE: If the finished wall is less than 5/8″ (1.6 cm) thick, no spline adapter will be used with the installation.

  • Determine the thickness of the finished wall.
  • If the finished wall is less than 5/8″ (1.6 cm) thick, use the 1″ (2.5 cm) long stem extension, 7/8″ (2.2 cm) long screw, and the 2″ (5.1 cm) long threaded sleeve.
  • If applicable, slide a spline adaptor onto the stem extension.
  • Place a stem extension on the valve stem. Secure with the screw provided. Thread a threaded sleeve onto the valve body.
  • Apply plumbers putty or another sealant to the back of the escutcheon according to the putty manufacturer’s instructions.
  • Thread an escutcheon onto the threaded sleeve. Remove any excess putty or sealant.
  • Press a handle over the stem extension and move the handle to the closed position (Hot = Counterclockwise, Cold = Clockwise). Lever handles should be horizontal when closed.

Wall-Mount Lavatory Faucet Trim

  • If adjustment is needed to achieve the desired handle alignment, remove the handle, screw and spline adapter or stem extension. Turn the spline adapter 1/4 turn. Check the handle position. Repeat the procedure until the proper handle position is achieved. Secure with the screw.
  • Thread the handle assembly onto the escutcheon. To maintain the proper handle alignment, hold the handle in place with one hand and turn the base of the handle with the other hand.
  • Repeat the procedures with the second handle.

3. Complete the Installation

  • Ensure that both faucet handles are turned off (hot = counterclockwise to close, cold = clockwise to close).
  • Turn on the water supplies and check the installation for leaks.
  • Repair as needed.
  • Remove the aerator.
  • Open the valves and run water through the spout for about a minute to remove any debris. Check for leaks.
  • Remove all debris from the aerator.
  • Turn the valves off, and reinstall the aerator.

Wall Mount 3 Piece Chrome Faucet Set

  • 2 cross handles for quick and easy water control
  • Low-arc spout with a 6-1/4 in. reach for ample room in the sink
  • Low-flow aerator option available (not included)
  • Solid brass construction for durability and reliability
  • Polished chrome finish resists corrosion and tarnishing for lasting beauty
  • Fluid design lines for ease of cleaning
  • Modern, minimal design is sure to coordinate well with the suite and accessories
  • Rough-in valve sold separately
  • ADA compliant
  • For a wall-mount installation.
Drain Installation

yon Wall Mount Single Handle Bathtub Faucet In Chrome Finish yon Wall Mount Single Handle Bathtub Faucet In Chrome Finish

  1. Remove rubber washer (4), friction ring (5) and locknut (6) from the drain assembly.
  2. Place a ring of silicone sealant beneath the lip of drain collar (3) and place it in the opening of the sink. Press down firmly to secure the drain collar (3).
  3. Screw rubber washer (4), friction ring (5) and locknut (6) onto drain collar yon Wall Mount Single Handle Bathtub Faucet In Chrome Finish
  4. For drain cartridge replacement or cleaning
    1. Remove cartridge (2) from drain: a) Push stopper to a raised position. Unscrew the stopper cap from the cartridge. b) Using a wrench or pliers, unscrew the cartridge from drain collar and remove from drain.

    yon Wall Mount Single Handle Bathtub Faucet In Chrome Finish
    5. Reinstall cartridge (2) into drain collar: a) Thread on stopper cap.


BathSelect Ancient Round Antique Rainfall Wall ShoweBathSelect Ancient Round Antique Rainfall Wall Shower Head Installation Instructions Head Installation Instructions